二臺H3C （S7003E）做簡單的堆疊配置

1、先規劃好需要做堆疊的端口與準備好堆疊線纜，堆疊口一般都是光口，看設備的情況而定。

2、將設備上電，并且使用堆疊線纜連接需要做堆疊設備與端口。

3、使用console線連接設備的console口開始配置。

4、配置如下：
①配置交換機的成員編號一般主的就是1，備的是2

主：
<H3C>sys
[H3C]irf member 1 renumber 1 選擇YES直接回車
[H3C]quit

備：
<H3C>sys
[H3C]irf member 1 renumber 2 選擇YES直接回車
[H3C]quit
重啟備設備

②配置交換機的成員優先級
主：
<H3C>sys
[H3C]irf member 1 priority 30
[H3C]quit
備：
<H3C>sys
[H3C]irf member 1 priority 15
[H3C]quit

③配置irf端口，進入所需要配置堆疊的物理端口關閉端口
主：
<H3C>sys
[H3C]int range Ten-GigabitEthernet 1/0/49 Ten-GigabitEthernet 1/0/50
[H3C-if-range]shutdown
[H3C-if-range]quit
[H3C]irf-port 1/1
[H3C-irf-port1/1]port group interface Ten-GigabitEthernet 1/0/49
[H3C-irf-port1/1]port group interface Ten-GigabitEthernet 1/0/50
[H3C-irf-port1/1]quit
[H3C]int range Ten-GigabitEthernet 1/0/49 Ten-GigabitEthernet 1/0/50
[H3C-if-range]undo shutdown
[H3C-if-range]quit
[H3C]save
[H3C] irf-port-configuration active

備：
<H3C>sys
[H3C]int range Ten-GigabitEthernet 2/0/49 Ten-GigabitEthernet 2/0/50
[H3C-if-range]shutdown
[H3C-if-range]quit
[H3C]irf-port 1/1
[H3C-irf-port1/1]port group interface Ten-GigabitEthernet 2/0/49
[H3C-irf-port1/1]port group interface Ten-GigabitEthernet 2/0/50
[H3C-irf-port1/1]quit
[H3C]int range Ten-GigabitEthernet 2/0/49 Ten-GigabitEthernet 2/0/50
[H3C-if-range]undo shutdown
[H3C-if-range]quit
[H3C]save
[H3C] irf-port-configuration active

注：配置完成之后會開始競選master，競選完成之后slave會自動重啟，
使用dis irf     查看堆疊情況 

④配置bfd檢測堆疊
配置BFD MAC

[H3C] vlan 3
[H3C-vlan3] port ten-gigabitethernet 1/0/24 ten-gigabitethernet 2/0/24
[H3C-vlan3] quit

[H3C] interface vlan-interface 3
[H3C-Vlan-interface3] mad bfd enable
[H3C-Vlan-interface3] mad ip address 192.168.2.1 24 member 1
[H3C-Vlan-interface3] mad ip address 192.168.2.2 24 member 2
[H3C-Vlan-interface3] quit

#BFD和stp互斥，關閉stp
[H3C] interface gigabitethernet 1/0/24
[H3C-gigabitethernet-1/0/1] undo stp enable
[H3C-gigabitethernet-1/0/1] quit
[H3C] interface gigabitethernet 2/0/24
[H3C-gigabitethernet-2/0/1] undo stp enable
[H3C-gigabitethernet-2/0/1] quit

網絡拓撲：