ceph中怎么配置集群訪問權限

這篇文章給大家介紹ceph中怎么配置集群訪問權限，內容非常詳細，感興趣的小伙伴們可以參考借鑒，希望對大家能有所幫助。

1、配置文件/etc/ceph/ceph.conf如下

[global]
    auth cluster required = cephx
    auth service required = cephx
    auth client required = cephx
    ;keyring = /etc/ceph/keyring
    ax open files = 131072
    log file = /var/log/ceph/$name.log
    pid file = /var/run/ceph/$name.pid
    osd pool default size = 2
    osd pool default min_size = 1
[mon]
    mon data = /data/$name
    ;keyring = /data/mon.0/keyring
[mon.0]
    host = ceph-one
    mon addr = 192.168.122.1:6789
;[mds]
;[mds.0]
    ;host = ceph-one
[osd]
    osd data = /data/$name
    osd journal = /data/$name/journal
    osd journal size = 1000
    osd mkfs type = xfs
    devs = /dev/ceph/$name
    osd crush update on start = 0
    ;keyring = /etc/ceph/keyring
[osd.0]
    host = ceph-one
[osd.1]
    host = ceph-two
[osd.2]
    host = ceph-three
[osd.3]
    host = ceph-four
[osd.4]
    host = ceph-five
[osd.5]
    host = ceph-six

如上所示auth cluster required=cepghx中三項全部配置為cephx選項，如果不做權限校驗全部配置為none

2、生成keyring文件

ceph-authtool --create-keyring /data/mon.0/ceph.mon.keyring --gen-key -n mon. --cap mon 'allow *'

上面的命令生成keyring文件在/data/mon.0/ceph.mon.keyring,如果不配置monitor使用默認keyring文件/data/mon.0/keyring,其中/data/mon.0是ceph.conf的mon data配置目錄
ceph auth get-or-create osd.0 mon 'allow rwx' osd 'allow *' -o /data/osd.0/keyring

上面命令生成osd的keyring

ceph auth get-or-create client.admin mds 'allow' osd 'allow *' mon 'allow *' > /etc/ceph/ceph.client.admin.keyring

上面命令生成client.admin的keyring，應該為rados的訪問命令。

3、rados使用keyring訪問代碼示例

#include <stdio.h>
#include <string.h>
#include <rados/librados.h>

   rados_t cluster; //聲明 集群句柄
    rados_ioctx_t io;
    char *poolname = "data";
    char cluster_name[] = "ceph";
    char user_name[] = "client.admin"; //用戶名
    uint64_t flags;
    char xattr[] = "en_US";
  int err;
 
  char *buf, *st;
  size_t buflen, stlen;
  char *cmd[2];
  cmd[1] = NULL;
 
  err = rados_create2(&cluster, cluster_name, user_name, flags); //創建集群句柄
 
  char fsid[50]={0};
    if (err < 0)
    {
        fprintf(stderr, "%s: Couldn't create the cluster handle! %s\n", argv[0], strerror(-err));
        exit(EXIT_FAILURE);
    }
    else
    {
        printf("\nCreated a cluster handle.\n");
    }


       //讀取配置文件，完成cluster句柄
  err = rados_conf_set(cluster,"mon_host", "127.0.0.1");
  err = rados_conf_set(cluster,"key", "AQDhSK9UeA+nOhAAhA7s2GLdU8seDVMBqK+iwg==");  
    //err = rados_conf_read_file(cluster, "/etc/ceph/ceph.conf");
    if (err < 0)
    {
        fprintf(stderr, "%s: cannot read config file: %s\n", argv[0], strerror(-err));
        exit(EXIT_FAILURE);
    }
    else
    {
        printf("\nRead the config file.\n");
    }

err = rados_connect(cluster);

注意rados_conf_set兩行代碼，我使用的ceph_test.c編譯命令行

gcc ceph_test.c -o ceph_test -lrados

關于ceph中怎么配置集群訪問權限就分享到這里了，希望以上內容可以對大家有一定的幫助，可以學到更多知識。如果覺得文章不錯，可以把它分享出去讓更多的人看到。