Brocade 光纖交換機常用命令

Brocade SAN交換機常用命令

使用電腦連接Brocade SAN交換機常用命令

使用電腦連接管理網口，默認IP地址為：192.168.0.1，掩碼：255.255.255.0

默認用戶名：admin，默認密碼password

1. switchStatusShow

查看交換機的總體健康狀態

switch:admin> switchstatusshow

Switch Health Report

Switch Name: SWFCR

IP address: 10.33.54.176

SwitchState: MARGINAL

Duration: 863:23

Power supplies monitor MARGINAL

Temperatures monitor HEALTHY

Fans monitor HEALTHY

WWN servers monitor HEALTHY

Standby CP monitor HEALTHY

Blades monitor HEALTHY

Flash monitor HEALTHY

Marginal ports monitor HEALTHY

Faulty ports monitor HEALTHY

Missing SFPs monitor HEALTHY

All ports are healthy

switch:admin>

2. switchShow

查看交換機基本配置信息

Enter the switchShow command, which displays the following information for a switch:

- switchname - The switch name.

- switchtype - The switch model and firmware version numbers.

- switchstate - The switch state: Online, Offline, Testing, or Faulty.

- switchrole - Displays the switch role: Principal, Subordinate, or Disabled.

- switchdomain - Displays the switch Domain ID.

- switchid - The embedded port D_ID of the switch.

- switchwwn - The switch World Wide Name.

- switchbeacon - The switch beaconing state: either ON or OFF.

The switchShow command also displays the following information for ports on the specified

switch:

- Module type - The SFP type if an SFP is present.

- Port speed - The speed of the Port (1G, 2G, 4G, N1, N2, N4, or AN). The speed can be

fixed, negotiated, or auto-negotiated.

- Port state - The port status.

- Comment - About the port. This section may be blank or display the WWN for an F_Port or

an E_Port, the trunking state, or upstream or downstream status

3. portShow

查看端口狀態

switch:admin> switch:user> portshow 0

portName:

portHealth: OFFLINE

Authentication: None

portDisableReason: None

portCFlags: 0x1

portFlags: 0x4001 PRESENT U_PORT LED

portType: 4.1

portState: 2 Offline

portPhys: 2 No_Module

portScn: 0

port generation number: 0

portId: 010000

portIfId: 43020020

portWwn: 20:00:00:60:69:00:02:53

portWwn of device(s) connected:

Distance: normal

portSpeed: N2Gbps

LE domain: 0

Interrupts: 0 Link_failure: 0 Frjt: 0

Unknown: 0 Loss_of_sync: 0 Fbsy: 0

Lli: 0 Loss_of_sig: 0

Proc_rqrd: 0 Protocol_err: 0

Timed_out: 0 Invalid_word: 0

Rx_flushed: 0 Invalid_crc: 0

Tx_unavail: 0 Delim_err: 0

Free_buffer: 0 Address_err: 0

Port part of other ADs: Yes

4. fanShow

查看交換機散熱風扇的狀態

Enter the fanShow command:

switch:admin> fanshow

Fan 1 is OK speed is 7010 RPM

Fan 2 is OK speed is 7180 RPM

Fan 3 is OK speed is 7068 RPM

Fan 4 is OK speed is 7116 RPM

Fan 5 is OK speed is 7155 RPM

Fan 6 is OK speed is 7001 RPM

switch:admin>

5. psShow

查看交換機的電源狀態

注：如果安裝FR4-18i、FC4-16IP、FC10-6、FC8-48板，需要滿配4個電源

Enter the psShow command:

switch:admin> psshow

Power Supply #1 is OK

0335,FF2Z0007161,60-0000739-02, B,,DCJ3002-01P, B,FF2Z0007161

Power Supply #2 is faulty

0335,FF2Z0007176,60-0000739-02, B,,DCJ3002-01P, B,FF2Z0007176

switch:admin>

6. tempShow

查看交換機的環境溫度

Enter the tempShow command:

switch:admin> tempshow

Index Status Centigrade Fahrenheit

----------------------------------------------------

1 OK 21 70

2 OK 22 72

3 OK 29 84

4 OK 24 75

5 OK 25 77

switch:admin>

7. errDump、errShow、errClear

查看交換機的內部消息日志

To display the system message log, with no page breaks

Enter the errDump command.

To display the system message log one at a time

Enter the errShow command.

To clear the system message log

Enter the errClear command.

8. supportShow、supportSave、pdShow

收集交換機的診斷數據

supportShow

顯示診斷信息和狀態信息

supportSave

將數據打包、上傳至指定的FTP服務器

The command prompts for an FTP server, packages the following files, and sends them to the specified server:

? The output of the supportShow command

? The contents of any trace dump files on the switch

? System message logs (for Brocade directors, supportSave saves the system message logs

from both of the CP blades)

pdShow

顯示panic dump文件的內容，幫助診斷系統panic的原因

9. nsShow、nsAllShow、fabricShow

檢查連接到交換機的設備

nsShow

顯示連接到交換機的所有設備

nsAllShow

顯示連接到Fabric的所有設備

fabricShow

顯示Fabric中的所有交換機

10. licenseShow、wwn

檢查license文件和交換機的WWN號

11. version

檢查Fabric OS的版本，將顯示如下信息：

- Kernel: displays the version of switch kernel operating system.

- Fabric OS: displays the version of switch Fabric OS.

- Made on: displays the build date of firmware running in switch.

- Flash: displays the install date of firmware stored in nonvolatile memory.

- BootProm: displays the version of the firmware stored in the boot PROM.

12. haShow

查看Control Blade的狀態

swDir: admin> haShow

Local CP (Slot 6, CP1): Active

Remote CP (Slot 5, CP0): Standby

HA Enabled, Heartbeat Up, State Synchronized

13. slotShow

查看各個Blade的狀態

14. portCfgSpeed

修改端口的速率

15. portEnable或portCfgPersistentEnable

Reset端口

16. 檢查WWN卡狀態

下列命令如果不能正確執行，則說明WWN卡需要更換：

www，chassisShow：顯示交換機的WWN號

chassisShow：顯示chassis和WWN卡的狀態

ipAddrShow，ipAddrSet：顯示CP Blades的IP地址

historyShow、historyLastShow：顯示歷史日志信息

switchName：顯示交換機的名字

修改Domain ID

1. 查看當前的Domain ID

輸入命令fabricShow，輸出結果中的Switch ID即包括交換機的Domain ID。

2. 先關閉交換機

輸入命令swichDisable

3. 配置DomainID

輸入命令configure

Enter y after the Fabric Parameters prompt:

Fabric parameters (yes, y, no, n): [no] y

Enter a unique domain ID at the Domain prompt. Use a domain ID value from 1 through 239 for normal operating mode (FCSW compatible):

Domain: (1..239) [1] 3

Respond to the remaining prompts, or press Ctrl-d to accept the other settings and exit.

4. 重新啟用交換機

輸入命令swichEnable

升級Firmware

FC10-6 Blade需要Firmware Version 5.3以上

FC4-16IP Blade、FC4-48 Port Blade需要Firmware Version 5.2以上

FR4-18i router blade需要Firmware Version 5.1以上

如果M48有主備Control Processor，且主備CP處于synchronized狀態，則升級過程可在線進行，不干擾數據流量。

如果M48只有一個CP，則升級微碼過程中需要reboot交換機來激活新的Firmware，數據訪問會中斷。

升級M48 Firmware約需15分鐘

1. 保存交換機的配置信息

configUpload

2. 保存主備Control Processor Blade的supportsave

使用命令ipAddrShow，查看主備CP的IP地址

使用telent分別登錄主備CP，使用命令supportSave分別收集主備CP的supportsave文件。

3. 查看supportsave中的XXX_SUPPORTSHOW文件，查找如下字段：

/bin/df:

Filesystem 1k-blocks Used Available Use% Mounted on

/dev/root 120112 61128 58984 51% /

/dev/hda2 120128 72356 47772 60% /mnt

確認Flash存儲器的使用率不超過90%。否則需聯系二線Support。

4. 清除交換機中當前保存的error report信息

errClear

5. 檢查當前各個CP Blades的Firmware版本

firmwareShow

6. 檢查主備CP狀態，是否處于同步狀態

haShow：查看主備CP是否處于Synchronized狀態

如果主備CP不處于同步狀態，則使用命令haSyncStart同步主備CP。

switch:admin> hashow

Local CP (Slot 5, CP0): Active, Warm Recovered

Remote CP (Slot 6, CP1): Standby, Healthy

HA enabled, Heartbeat Up, HA State synchronized

7. 升級Firmware

如果SAN交換機支持HA，則使用命令firmwareDownload，同時升級主備Control Blade。

如果SAN交換機不支持HA，則使用命令firmwareDownload-s，分別升級每個Control Blade。

8. 檢查Firmware升級是否完成

firmwareDownloadStatus

9. 再次檢查當前各個CP Blades的Firmware版本

firmwareShow

激活軟件License

1. 查看當前已經激活的License

licenseShow

swDir:admin> licenseShow

AAbbccDDeeFFeeGG:

Web license

Zoning license

Extended Fabric license

Fabric Watch license

Performance Monitor license

Trunking license

Security license

2. 獲取和激活License時需要提供64位的ChasisID，查看Chasis ID：

licenseIdShow

3. 激活新的License

licenseAdd “key”

4. 刪除舊的License

licenseRemove “key”

刪除License后需要reboot交換機，或者switchDisable/switchEnable重啟交換機，以使需要刪除的License失效。

備份交換機的配置信息

1. 使用configUpload命令，將配置文件保存在自己的電腦上

注：configUpload無法保存用戶的密碼信息。

2. 使用Telnet命令查看配置信息，并做Session Log

configShow

ipaddrShow

licenseShow

switchShow

3. 保存SupportSave文件

supportSave

安裝/更換Port Blade

1. 查看當前Port Blade的狀態

switchShow

2. 查看需要更換的Port Blade的備件號

chassisShow

包含有Port Blade的備件號、序列號和狀態。

3. 確認需要更換的Port Blade上已經沒有數據流量

查看Port Blade狀態LED，確保所有的Port Speed和Port Status狀態燈處于OFF狀態。

4. 安裝/更換完畢后檢查

nsShow

nsAllShow

fabricShow

更換M48 CP(Control Processor) Blade

估計用時30分鐘

注意事項：

1. 在拿到新CP Blade備件，可以開始物理更換前，不要將故障CP Blade取出，以免影響散熱。

2. Acitve狀態的CP Blade將自動把配置信息鏡像到Standby狀態的CP Blade上。必須在線更換CP Blade，才能實現配置信息的自動同步。

3. 新換上的CP Blade將繼承舊CP Blade的IP地址和主機名。

4. 確保兩個CP Blade處于同一FOS版本。

更換前的檢查：

1. 查看CPBlade上的Status LED是否為×××，PowerLED是否點亮。

2. 使用slotShow命令查看CP Blade是否處于Enabled狀態。

3. 使用hsShow命令是否報錯。

4. 使用errShow命令查看錯誤日志。

備份配置信息：

1. 切換健康的CP Blade為當前Active狀態的CPBlade。

使用命令haFailover，實現CP Blade間的手動切換。

使用命令haShow，確認當前Active狀態的CPBlade為健康的CP Blade。

等待CP Blade上的Status LED熄滅，表明HA Failover已經完成。

2. 使用firmwareShow命令檢查Firmware版本

3. 使用haDisable命令，暫時取消Failover功能。

4. 使用configUpload命令保存配置信息。

swDir:admin> configUpload

Protocol (scp or ftp) [ftp]: ftp

Server Name or IP Address [host]: 123.456.78.90

User Name [None]: user

File Name [config.txt]: config.txt

Password: xxxxxxxx

upload complete

更換CP Blade

1. 將CPBlade上的電源開關撥至Down位置，切斷CP Blade的電源。

2. 拔下CPBlade。

3. 插入新的CP Blade。

4. 將CPBlade上的電源開關撥至Up位置，給CP Blade供電。

更換后的驗證：

1. 等待兩個CP Blade上的Status LED都熄滅。

2. 使用命令haEnable啟用HA Failover功能。

3. 使用命令haShow檢查HA狀態，確認“HAEnabled Heartbeat Up” and “HA-statein sync”。

4. 使用命令slotShow檢查所有的CP Blade都處于Enabled狀態。

swDir:admin> slotShow

Slot Blade Type ID Status ---------------------------------

1 SW BLADE 17 ENABLED

2 SW BLADE 17 ENABLED

3 SW BLADE 17 ENABLED

4 SW BLADE 17 ENABLED

5 CP BLADE 16 ENABLED

6 CP BLADE 16 ENABLED

7 SW BLADE 17 ENABLED

8 SW BLADE 17 ENABLED

9 SW BLADE 17 ENABLED

10 SW BLADE 17 ENABLED

swDir:admin>

5. 使用命令firmwareShow命令，檢查FW版本是否一致

swDir:admin> firmwareShow

Local CP (Slot 6, CP1): Active

Primary partition: v5.0.1

Secondary Partition: v5.0.1

Remote CP (Slot 5, CP0): Standby

Primary partition: v5.0.1

Secondary Partition: v5.0.1

Note: If Local CP and Remote CP have different versions of firmware, please retry firmwaredownload command.

swDir:admin>

6. 使用firmwareDownload-s命令，只升級單獨某個CP Blade的微碼。

7. 使用firmwareDownloadStatus命令，驗證微碼安裝是否成功。

ZONE配置

1. 概念

zone configuration：

為一組zone的集合。一個zone可以同時屬于不同的zone configuration之中。當一個zone configuration生效時，屬于該zone configuration的所有zone都生效。

創建zone配置基本步驟：

創建alias -> 創建zone -> 創建zone configuration -> cfgSave -> cfgEnable

2. 常用命令

configUpload：備份zone configuration

configDownload：恢復zone configuration

3. 創建別名

（1）aliCreate

（2）cfgSave

switch:admin> alicreate "array1", "2,32; 2,33; 2,34; 4,4"

switch:admin> alicreate "array2", "21:00:00:20:37:0c:66:23; 4,3"

switch:admin> alicreate "loop1", "4,6"

switch:admin> cfgsave

You are about to save the Defined zoning configuration. This

action will only save the changes on the Defined configuration.

Any changes made on the Effective configuration will not

take effect until it is re-enabled.

Do you want to save Defined zoning configuration only? (yes, y, no, n): [no] y

4. 向別名中增加成員

（1）aliAdd

（2）cfgSave

switch:admin> aliadd "array1", "1,2"

switch:admin> aliadd "array2", "21:00:00:20:37:0c:72:51"

switch:admin> aliadd "loop1", "5,6"

switch:admin> cfgsave

You are about to save the Defined zoning configuration. This

action will only save the changes on the Defined configuration.

Any changes made on the Effective configuration will not

take effect until it is re-enabled.

Do you want to save Defined zoning configuration only? (yes, y, no, n): [no] y

5. 刪除別名中的成員

（1）aliRemove

（2）cfgSave

switch:admin> aliremove "array1", "1,2"

switch:admin> aliremove "array2", "21:00:00:20:37:0c:72:51"

switch:admin> aliremove "loop1", "4,6"

switch:admin> cfgsave

You are about to save the Defined zoning configuration. This

action will only save the changes on the Defined configuration.

Any changes made on the Effective configuration will not

take effect until it is re-enabled.

Do you want to save Defined zoning configuration only? (yes, y, no, n): [no] y

6. 刪除別名

switch:admin> alidelete "array1"

switch:admin> cfgsave

7. 查看定義配置中的別名

switch:admin> alishow "arr*"

alias: array1 21:00:00:20:37:0c:76:8c

alias: array2 21:00:00:20:37:0c:66:23

8. 創建zone

switch:admin> zonecreate "greenzone","2,32; 2,33; 2,34; 4,4"

switch:admin> zonecreate "redzone","21:00:00:20:37:0c:66:23; 4,3"

switch:admin> zonecreate "broadcast","1,2; 2,33; 2,34"

switch:admin> cfgsave

9. 向zone中增加設備

switch:admin> zoneadd "greenzone","1,2"

switch:admin> zoneadd "redzone","21:00:00:20:37:0c:72:51"

switch:admin> zoneadd "broadcast","1,3"

switch:admin> cfgsave

10. 從zone中刪除設備

switch:admin> zoneremove "greenzone","1,2"

switch:admin> zoneremove "redzone","21:00:00:20:37:0c:72:51"

switch:admin> zoneremove "broadcast","2,34"

switch:admin> cfgsave

11. 刪除一個zone

switch:admin> zonedelete "redzone"

switch:admin> cfgsave

12. 查看當前定義配置中的zone

以下命令查看所有以字母A、B、C開頭的zone

switch:admin> zoneshow "[A-C]*"

zone: Blue_zone 1,1; array1; 1,2; array2

zone: Bobs_zone 4,5; 4,6; 4,7; 4,8; 4,9

13. 創建zone配置

switch:admin> cfgcreate "NEW_cfg","redzone; bluezone; greenzone"

switch:admin> cfgsave

14. 向zone配置成員中加入zone

switch:admin> cfgadd "newcfg","bluezone"

switch:admin> cfgsave

15. 從zone配置成員中刪除zone

switch:admin> cfgremove "NEW_cfg", "redzone"

switch:admin> cfgsave

16. 刪除zone配置

switch:admin> cfgdelete "testcfg"

switch:admin> cfgsave

17. 撤銷對zone配置的修改

命令cfgTransAbort將撤銷所有未保存的修改，及恢復到上次執行cfgSave時的狀態。

18. 查看zone配置信息

cfgShow不帶任何參數：顯示處于defined和effective狀態的所有zone配置信息

switch:admin> cfgshow

Defined configuration:

cfg: USA1 Blue_zone

cfg: USA_cfg Red_zone; Blue_zone

zone: Blue_zone

1,1; array1; 1,2; array2

zone: Red_zone

1,0; loop1

alias: array1 21:00:00:20:37:0c:76:8c;21:00:00:20:37:0c:71:02

alias: array2 21:00:00:20:37:0c:76:22; 21:00:00:20:37:0c:76:28

alias: loop1 21:00:00:20:37:0c:76:85;21:00:00:20:37:0c:71:df

Effective configuration:

cfg: USA_cfg

zone: Blue_zone

1,1

21:00:00:20:37:0c:76:8c

21:00:00:20:37:0c:71:02

1,2

21:00:00:20:37:0c:76:22

21:00:00:20:37:0c:76:28

zone: Red_zone

1,0

21:00:00:20:37:0c:76:85

21:00:00:20:37:0c:71:df

19. 保存zone配置

switch:admin> cfgenable "USA_cfg"

You are about to enable a new zoning configuration.

This action will replace the old zoning configurationwith the

current configuration selected.

Do you want to enable 'USA_cfg' configuration (yes, y,no, n): [no] y

zone config "USA_cfg" is in effect

Updating flash ...

管理網口，默認IP地址為：192.168.0.1，掩碼：255.255.255.0

默認用戶名：admin，默認密碼password

1. switchStatusShow

查看交換機的總體健康狀態

switch:admin> switchstatusshow

Switch Health Report

Switch Name: SWFCR

IP address: 10.33.54.176

SwitchState: MARGINAL

Duration: 863:23

Power supplies monitor MARGINAL

Temperatures monitor HEALTHY

Fans monitor HEALTHY

WWN servers monitor HEALTHY

Standby CP monitor HEALTHY

Blades monitor HEALTHY

Flash monitor HEALTHY

Marginal ports monitor HEALTHY

Faulty ports monitor HEALTHY

Missing SFPs monitor HEALTHY

All ports are healthy

switch:admin>

2. switchShow

查看交換機基本配置信息

Enter the switchShow command, which displays the following information for a switch:

- switchname - The switch name.

- switchtype - The switch model and firmware version numbers.

- switchstate - The switch state: Online, Offline, Testing, or Faulty.

- switchrole - Displays the switch role: Principal, Subordinate, or Disabled.

- switchdomain - Displays the switch Domain ID.

- switchid - The embedded port D_ID of the switch.

- switchwwn - The switch World Wide Name.

- switchbeacon - The switch beaconing state: either ON or OFF.

The switchShow command also displays the following information for ports on the specified

switch:

- Module type - The SFP type if an SFP is present.

- Port speed - The speed of the Port (1G, 2G, 4G, N1, N2, N4, or AN). The speed can be

fixed, negotiated, or auto-negotiated.

- Port state - The port status.

- Comment - About the port. This section may be blank or display the WWN for an F_Port or

an E_Port, the trunking state, or upstream or downstream status

3. portShow

查看端口狀態

switch:admin> switch:user> portshow 0

portName:

portHealth: OFFLINE

Authentication: None

portDisableReason: None

portCFlags: 0x1

portFlags: 0x4001 PRESENT U_PORT LED

portType: 4.1

portState: 2 Offline

portPhys: 2 No_Module

portScn: 0

port generation number: 0

portId: 010000

portIfId: 43020020

portWwn: 20:00:00:60:69:00:02:53

portWwn of device(s) connected:

Distance: normal

portSpeed: N2Gbps

LE domain: 0

Interrupts: 0 Link_failure: 0 Frjt: 0

Unknown: 0 Loss_of_sync: 0 Fbsy: 0

Lli: 0 Loss_of_sig: 0

Proc_rqrd: 0 Protocol_err: 0

Timed_out: 0 Invalid_word: 0

Rx_flushed: 0 Invalid_crc: 0

Tx_unavail: 0 Delim_err: 0

Free_buffer: 0 Address_err: 0

Port part of other ADs: Yes

4. fanShow

查看交換機散熱風扇的狀態

Enter the fanShow command:

switch:admin> fanshow

Fan 1 is OK speed is 7010 RPM

Fan 2 is OK speed is 7180 RPM

Fan 3 is OK speed is 7068 RPM

Fan 4 is OK speed is 7116 RPM

Fan 5 is OK speed is 7155 RPM

Fan 6 is OK speed is 7001 RPM

switch:admin>

5. psShow

查看交換機的電源狀態

注：如果安裝FR4-18i、FC4-16IP、FC10-6、FC8-48板，需要滿配4個電源

Enter the psShow command:

switch:admin> psshow

Power Supply #1 is OK

0335,FF2Z0007161,60-0000739-02, B,,DCJ3002-01P, B,FF2Z0007161

Power Supply #2 is faulty

0335,FF2Z0007176,60-0000739-02, B,,DCJ3002-01P, B,FF2Z0007176

switch:admin>

6. tempShow

查看交換機的環境溫度

Enter the tempShow command:

switch:admin> tempshow

Index Status Centigrade Fahrenheit

----------------------------------------------------

1 OK 21 70

2 OK 22 72

3 OK 29 84

4 OK 24 75

5 OK 25 77

switch:admin>

7. errDump、errShow、errClear

查看交換機的內部消息日志

To display the system message log, with no page breaks

Enter the errDump command.

To display the system message log one at a time

Enter the errShow command.

To clear the system message log

Enter the errClear command.

8. supportShow、supportSave、pdShow

收集交換機的診斷數據

supportShow

顯示診斷信息和狀態信息

supportSave

將數據打包、上傳至指定的FTP服務器

The command prompts for an FTP server, packages the following files, and sends them to the specified server:

? The output of the supportShow command

? The contents of any trace dump files on the switch

? System message logs (for Brocade directors, supportSave saves the system message logs

from both of the CP blades)

pdShow

顯示panic dump文件的內容，幫助診斷系統panic的原因

9. nsShow、nsAllShow、fabricShow

檢查連接到交換機的設備

nsShow

顯示連接到交換機的所有設備

nsAllShow

顯示連接到Fabric的所有設備

fabricShow

顯示Fabric中的所有交換機

10. licenseShow、wwn

檢查license文件和交換機的WWN號

11. version

檢查Fabric OS的版本，將顯示如下信息：

- Kernel: displays the version of switch kernel operating system.

- Fabric OS: displays the version of switch Fabric OS.

- Made on: displays the build date of firmware running in switch.

- Flash: displays the install date of firmware stored in nonvolatile memory.

- BootProm: displays the version of the firmware stored in the boot PROM.

12. haShow

查看Control Blade的狀態

swDir: admin> haShow

Local CP (Slot 6, CP1): Active

Remote CP (Slot 5, CP0): Standby

HA Enabled, Heartbeat Up, State Synchronized

13. slotShow

查看各個Blade的狀態

14. portCfgSpeed

修改端口的速率

15. portEnable或portCfgPersistentEnable

Reset端口

16. 檢查WWN卡狀態

下列命令如果不能正確執行，則說明WWN卡需要更換：

www，chassisShow：顯示交換機的WWN號

chassisShow：顯示chassis和WWN卡的狀態

ipAddrShow，ipAddrSet：顯示CP Blades的IP地址

historyShow、historyLastShow：顯示歷史日志信息

switchName：顯示交換機的名字

修改Domain ID

1. 查看當前的Domain ID

輸入命令fabricShow，輸出結果中的Switch ID即包括交換機的Domain ID。

2. 先關閉交換機

輸入命令swichDisable

3. 配置DomainID

輸入命令configure

Enter y after the Fabric Parameters prompt:

Fabric parameters (yes, y, no, n): [no] y

Enter a unique domain ID at the Domain prompt. Use a domain ID value from 1 through 239 for normal operating mode (FCSW compatible):

Domain: (1..239) [1] 3

Respond to the remaining prompts, or press Ctrl-d to accept the other settings and exit.

4. 重新啟用交換機

輸入命令swichEnable

升級Firmware

FC10-6 Blade需要Firmware Version 5.3以上

FC4-16IP Blade、FC4-48 Port Blade需要Firmware Version 5.2以上

FR4-18i router blade需要Firmware Version 5.1以上

如果M48有主備Control Processor，且主備CP處于synchronized狀態，則升級過程可在線進行，不干擾數據流量。

如果M48只有一個CP，則升級微碼過程中需要reboot交換機來激活新的Firmware，數據訪問會中斷。

升級M48 Firmware約需15分鐘

1. 保存交換機的配置信息

configUpload

2. 保存主備Control Processor Blade的supportsave

使用命令ipAddrShow，查看主備CP的IP地址

使用telent分別登錄主備CP，使用命令supportSave分別收集主備CP的supportsave文件。

3. 查看supportsave中的XXX_SUPPORTSHOW文件，查找如下字段：

/bin/df:

Filesystem 1k-blocks Used Available Use% Mounted on

/dev/root 120112 61128 58984 51% /

/dev/hda2 120128 72356 47772 60% /mnt

確認Flash存儲器的使用率不超過90%。否則需聯系二線Support。

4. 清除交換機中當前保存的error report信息

errClear

5. 檢查當前各個CP Blades的Firmware版本

firmwareShow

6. 檢查主備CP狀態，是否處于同步狀態

haShow：查看主備CP是否處于Synchronized狀態

如果主備CP不處于同步狀態，則使用命令haSyncStart同步主備CP。

switch:admin> hashow

Local CP (Slot 5, CP0): Active, Warm Recovered

Remote CP (Slot 6, CP1): Standby, Healthy

HA enabled, Heartbeat Up, HA State synchronized

7. 升級Firmware

如果SAN交換機支持HA，則使用命令firmwareDownload，同時升級主備Control Blade。

如果SAN交換機不支持HA，則使用命令firmwareDownload-s，分別升級每個Control Blade。

8. 檢查Firmware升級是否完成

firmwareDownloadStatus

9. 再次檢查當前各個CP Blades的Firmware版本

firmwareShow

激活軟件License

1. 查看當前已經激活的License

licenseShow

swDir:admin> licenseShow

AAbbccDDeeFFeeGG:

Web license

Zoning license

Extended Fabric license

Fabric Watch license

Performance Monitor license

Trunking license

Security license

2. 獲取和激活License時需要提供64位的ChasisID，查看Chasis ID：

licenseIdShow

3. 激活新的License

licenseAdd “key”

4. 刪除舊的License

licenseRemove “key”

刪除License后需要reboot交換機，或者switchDisable/switchEnable重啟交換機，以使需要刪除的License失效。

備份交換機的配置信息

1. 使用configUpload命令，將配置文件保存在自己的電腦上

注：configUpload無法保存用戶的密碼信息。

2. 使用Telnet命令查看配置信息，并做Session Log

configShow

ipaddrShow

licenseShow

switchShow

3. 保存SupportSave文件

supportSave

安裝/更換Port Blade

1. 查看當前Port Blade的狀態

switchShow

2. 查看需要更換的Port Blade的備件號

chassisShow

包含有Port Blade的備件號、序列號和狀態。

3. 確認需要更換的Port Blade上已經沒有數據流量

查看Port Blade狀態LED，確保所有的Port Speed和Port Status狀態燈處于OFF狀態。

4. 安裝/更換完畢后檢查

nsShow

nsAllShow

fabricShow

更換M48 CP(Control Processor) Blade

估計用時30分鐘

注意事項：

1. 在拿到新CP Blade備件，可以開始物理更換前，不要將故障CP Blade取出，以免影響散熱。

2. Acitve狀態的CP Blade將自動把配置信息鏡像到Standby狀態的CP Blade上。必須在線更換CP Blade，才能實現配置信息的自動同步。

3. 新換上的CP Blade將繼承舊CP Blade的IP地址和主機名。

4. 確保兩個CP Blade處于同一FOS版本。

更換前的檢查：

1. 查看CPBlade上的Status LED是否為×××，PowerLED是否點亮。

2. 使用slotShow命令查看CP Blade是否處于Enabled狀態。

3. 使用hsShow命令是否報錯。

4. 使用errShow命令查看錯誤日志。

備份配置信息：

1. 切換健康的CP Blade為當前Active狀態的CPBlade。

使用命令haFailover，實現CP Blade間的手動切換。

使用命令haShow，確認當前Active狀態的CPBlade為健康的CP Blade。

等待CP Blade上的Status LED熄滅，表明HA Failover已經完成。

2. 使用firmwareShow命令檢查Firmware版本

3. 使用haDisable命令，暫時取消Failover功能。

4. 使用configUpload命令保存配置信息。

swDir:admin> configUpload

Protocol (scp or ftp) [ftp]: ftp

Server Name or IP Address [host]: 123.456.78.90

User Name [None]: user

File Name [config.txt]: config.txt

Password: xxxxxxxx

upload complete

更換CP Blade

1. 將CPBlade上的電源開關撥至Down位置，切斷CP Blade的電源。

2. 拔下CPBlade。

3. 插入新的CP Blade。

4. 將CPBlade上的電源開關撥至Up位置，給CP Blade供電。

更換后的驗證：

1. 等待兩個CP Blade上的Status LED都熄滅。

2. 使用命令haEnable啟用HA Failover功能。

3. 使用命令haShow檢查HA狀態，確認“HAEnabled Heartbeat Up” and “HA-statein sync”。

4. 使用命令slotShow檢查所有的CP Blade都處于Enabled狀態。

swDir:admin> slotShow

Slot Blade Type ID Status ---------------------------------

1 SW BLADE 17 ENABLED

2 SW BLADE 17 ENABLED

3 SW BLADE 17 ENABLED

4 SW BLADE 17 ENABLED

5 CP BLADE 16 ENABLED

6 CP BLADE 16 ENABLED

7 SW BLADE 17 ENABLED

8 SW BLADE 17 ENABLED

9 SW BLADE 17 ENABLED

10 SW BLADE 17 ENABLED

swDir:admin>

5. 使用命令firmwareShow命令，檢查FW版本是否一致

swDir:admin> firmwareShow

Local CP (Slot 6, CP1): Active

Primary partition: v5.0.1

Secondary Partition: v5.0.1

Remote CP (Slot 5, CP0): Standby

Primary partition: v5.0.1

Secondary Partition: v5.0.1

Note: If Local CP and Remote CP have different versions of firmware, please retry firmwaredownload command.

swDir:admin>

6. 使用firmwareDownload-s命令，只升級單獨某個CP Blade的微碼。

7. 使用firmwareDownloadStatus命令，驗證微碼安裝是否成功。

ZONE配置

1. 概念

zone configuration：

為一組zone的集合。一個zone可以同時屬于不同的zone configuration之中。當一個zone configuration生效時，屬于該zone configuration的所有zone都生效。

創建zone配置基本步驟：

創建alias -> 創建zone -> 創建zone configuration -> cfgSave -> cfgEnable

2. 常用命令

configUpload：備份zone configuration

configDownload：恢復zone configuration

3. 創建別名

（1）aliCreate

（2）cfgSave

switch:admin> alicreate "array1", "2,32; 2,33; 2,34; 4,4"

switch:admin> alicreate "array2", "21:00:00:20:37:0c:66:23; 4,3"

switch:admin> alicreate "loop1", "4,6"

switch:admin> cfgsave

You are about to save the Defined zoning configuration. This

action will only save the changes on the Defined configuration.

Any changes made on the Effective configuration will not

take effect until it is re-enabled.

Do you want to save Defined zoning configuration only? (yes, y, no, n): [no] y

4. 向別名中增加成員

（1）aliAdd

（2）cfgSave

switch:admin> aliadd "array1", "1,2"

switch:admin> aliadd "array2", "21:00:00:20:37:0c:72:51"

switch:admin> aliadd "loop1", "5,6"

switch:admin> cfgsave

You are about to save the Defined zoning configuration. This

action will only save the changes on the Defined configuration.

Any changes made on the Effective configuration will not

take effect until it is re-enabled.

Do you want to save Defined zoning configuration only? (yes, y, no, n): [no] y

5. 刪除別名中的成員

（1）aliRemove

（2）cfgSave

switch:admin> aliremove "array1", "1,2"

switch:admin> aliremove "array2", "21:00:00:20:37:0c:72:51"

switch:admin> aliremove "loop1", "4,6"

switch:admin> cfgsave

You are about to save the Defined zoning configuration. This

action will only save the changes on the Defined configuration.

Any changes made on the Effective configuration will not

take effect until it is re-enabled.

Do you want to save Defined zoning configuration only? (yes, y, no, n): [no] y

6. 刪除別名

switch:admin> alidelete "array1"

switch:admin> cfgsave

7. 查看定義配置中的別名

switch:admin> alishow "arr*"

alias: array1 21:00:00:20:37:0c:76:8c

alias: array2 21:00:00:20:37:0c:66:23

8. 創建zone

switch:admin> zonecreate "greenzone","2,32; 2,33; 2,34; 4,4"

switch:admin> zonecreate "redzone","21:00:00:20:37:0c:66:23; 4,3"

switch:admin> zonecreate "broadcast","1,2; 2,33; 2,34"

switch:admin> cfgsave

9. 向zone中增加設備

switch:admin> zoneadd "greenzone","1,2"

switch:admin> zoneadd "redzone","21:00:00:20:37:0c:72:51"

switch:admin> zoneadd "broadcast","1,3"

switch:admin> cfgsave

10. 從zone中刪除設備

switch:admin> zoneremove "greenzone","1,2"

switch:admin> zoneremove "redzone","21:00:00:20:37:0c:72:51"

switch:admin> zoneremove "broadcast","2,34"

switch:admin> cfgsave

11. 刪除一個zone

switch:admin> zonedelete "redzone"

switch:admin> cfgsave

12. 查看當前定義配置中的zone

以下命令查看所有以字母A、B、C開頭的zone

switch:admin> zoneshow "[A-C]*"

zone: Blue_zone 1,1; array1; 1,2; array2

zone: Bobs_zone 4,5; 4,6; 4,7; 4,8; 4,9

13. 創建zone配置

switch:admin> cfgcreate "NEW_cfg","redzone; bluezone; greenzone"

switch:admin> cfgsave

14. 向zone配置成員中加入zone

switch:admin> cfgadd "newcfg","bluezone"

switch:admin> cfgsave

15. 從zone配置成員中刪除zone

switch:admin> cfgremove "NEW_cfg","redzone"

switch:admin> cfgsave

16. 刪除zone配置

switch:admin> cfgdelete "testcfg"

switch:admin> cfgsave

17. 撤銷對zone配置的修改

命令cfgTransAbort將撤銷所有未保存的修改，及恢復到上次執行cfgSave時的狀態。

18. 查看zone配置信息

cfgShow不帶任何參數：顯示處于defined和effective狀態的所有zone配置信息

switch:admin> cfgshow

Defined configuration:

cfg: USA1 Blue_zone

cfg: USA_cfg Red_zone; Blue_zone

zone: Blue_zone

1,1; array1; 1,2; array2

zone: Red_zone

1,0; loop1

alias: array1 21:00:00:20:37:0c:76:8c;21:00:00:20:37:0c:71:02

alias: array2 21:00:00:20:37:0c:76:22; 21:00:00:20:37:0c:76:28

alias: loop1 21:00:00:20:37:0c:76:85;21:00:00:20:37:0c:71:df

Effective configuration:

cfg: USA_cfg

zone: Blue_zone

1,1

21:00:00:20:37:0c:76:8c

21:00:00:20:37:0c:71:02

1,2

21:00:00:20:37:0c:76:22

21:00:00:20:37:0c:76:28

zone: Red_zone

1,0

21:00:00:20:37:0c:76:85

21:00:00:20:37:0c:71:df

19. 保存zone配置

switch:admin> cfgenable "USA_cfg"

You are about to enable a new zoning configuration.

This action will replace the old zoning configurationwith the

current configuration selected.

Do you want to enable 'USA_cfg' configuration (yes, y,no, n): [no] y

zone config "USA_cfg" is in effect

Updating flash ...